Sweex LW321 Installationsanleitung

4LW320/LW321 Sweex Wireless 300N Router• Do not expose the Sweex Wireless 300N Router to extreme temperatures. Do not place the device in direct sun

13You should see the Internet Configuration Wizard screen: You can now proceed with the advanced setup using one of the configurations described furth

14Configuration 2: PPPoEIf your ISP requires the PPPoE connection type, click the “PPPoE” button. You will see the following screen: Enter your accoun

15Fill out all fields as required by your ISP and then choose “Finish”.During all selections you will have an option to configure the “Basic” wireless

16Wireless network configurationIt is recommended to only adjust wireless settings from a computer connected to the router by network cable, especiall

17Channel WidthIn this section it is possible to manually select the channel width (20/40MHz), it is recommended to keep the default setting.Max Tx Ra

18 Method 1: WEPSecuring your network with WEP is done in 3 steps:1. Select the following settings: Type: “Automatic” (it is recommended to use the

19After a WPS secured connection has been set up for the first time, all previously connected devices will lose their connection. You will have to con

20To configure a device for a static DHCP address, fill out the device’s corresponding MAC address in the “MAC Address” section and fill in the “desir

21For a DMZ, click “DMZ” in the menu on the left, enter the IP address of the device, check the “Enable” checkbox and click the “Save” button.Bandwidt

22English versionTroubleshootingThis chapter of the manual will explain a number of common issues that you may run into and possible solutions.• I ca

5English versionProduct descriptionFront1. Power LED: This light indicates that the router receives power.2. READY LED: A constantly blinking SYS li

23English version3. Right click the first connected LAN or High-Speed Internet Connection, in this example the “Local Area Connection”, and click “P

245. The Internet Protocol’s property window appears. In this window, ensure that both settings are set to “Obtain automatically”:6. Confirm the

252. In the Control Panel, click “View network status and tasks”. If your Control Panel is in classic view, open the “Network and Sharing Center” i

26English version4. Right click the first connected LAN or High-Speed Internet Connection, in this example the “Local Area Connection”, and click “P

27English version6. The Internet Protocol Version 4’s property window appears. In this window, ensure that both settings are set to “Obtain automatic

282. In the Control Panel, click “View network status and tasks”. If your Control Panel is in icon view, open the “Network and Sharing Center” icon

294. Right click the first connected connection, in this example the “Local Area Connection”, and click “Properties” from the context menu. If you

306. The Internet Protocol Version 4’s property window appears. In this window, ensure that both settings are set to “Obtain automatically”: 7. Conf

313. In this window, click the “Connections” tab and in this tab, the “LAN Settings” button.4. The “LAN Settings” window will now open. Ensure that

32• My computer indicates that it is not connected to a network.• This problem is usually resolved by carefully checking all connections and indica

6Back 1. DC power input: Connect the supplied power adapter to this input. If the adapter is lost it can be replaced by a similar model with 9 V

333. The Manage Wireless Networks window now opens. In this window, select the conflicting network and click “Remove”. After the network has been de

343. In the Network and Sharing Center, click “Manage wireless networks”: 4. The following window will appear, right click the network that was indic

35• I have lost the WPA or WEP key required to access my wireless network.• There are two possible solutions for this issue:1. Access the router

36Warranty2-year standard warranty within the EU• In a standard manner a warranty period of 2 years as from the purchase date is available for this S

7English versionSimple setupSimple setup is done in 7 steps:1. Disconnect the power to your modem. If one or more computers were connected to your mo

8Connecting to a wireless network• Windows XP: Right click on your wireless adapter’s icon at the bottom right of your screen and click “View Availa

9Note: If you see a red cross near the network and the text: “The settings saved on this computer for the network do not match the requirements of the

10 Windows 7: Windows 7 will indicate when wireless networks are available. You can recognise this by the following icon in the bottom-right of your s

11The following screen will appear, enter the desired name for your wireless network and click “Next” to begin configuring the router:Note: The defaul

12Advanced setupAdvanced setup can be done when you know exactly which settings your ISP requires or when the simple setup fails.There are 4 possible